Garages · Workshops · Commercial Floors
Epoxy Flooring Comox BC
A finished floor that works as hard as your space.
Priority One Epoxy Flooring installs epoxy, full-flake and polyaspartic floor coatings for Comox garages, shops, commercial spaces and hangars. We assess the concrete, prepare it mechanically and match the coating layers to your traffic, moisture conditions, cleaning needs and schedule.
Experience and completed-floor totals refer to our company-wide portfolio.
Floor coatings for Comox homes and businesses
Choose the floor around how the space is used. A family garage, a repair shop and an aircraft hangar need different preparation, texture and wear layers.
Residential
Garage and workshop floors
Full-flake finishes for vehicle parking, tools, bikes and storage. We review cracks, oil contamination and existing paint before specifying the basecoat and topcoat.
Commercial
Shops and service spaces
Solid-colour, flake and quartz systems for shops, service bays, storage rooms and commercial work areas. Texture and chemical resistance are selected for the actual work and cleaning routine.
Specialty projects
Hangars and equipment storage
Project-specific systems for hangars, equipment bays and indoor marine or RV storage. Tell us about rolling equipment, fluids, drainage and reopening deadlines so we can review the right specification.
See the finish before choosing your floor
These photos show work from our wider company portfolio. They illustrate finish options for your Comox project; the actual project locations are identified below.
Compare epoxy and polyaspartic flooring systems
Epoxy and polyaspartic can be different layers in the same floor. The complete build matters: prepared concrete, a compatible primer or basecoat, the finish layer and the selected topcoat.
Full-flake garage systems
A decorative flake broadcast creates a consistent, textured appearance. A specified UV-stable polyaspartic topcoat is an option where sunlight reaches the floor through open doors.
Often considered for: garages, home workshops and storage spaces.
Solid-colour and high-build epoxy
A uniform finish for practical workspaces. Thickness, repairs and the wear coat are selected around tools, trolley traffic, vehicles and the chemicals used on site.
Often considered for: shops, service rooms, equipment bays and warehouses.
Quartz and textured broadcast systems
Aggregate and the sealing coats can be specified to improve traction. Texture is balanced against cleanability rather than assuming the roughest finish is best for every floor.
Often considered for: wet-use work areas, entrances and selected commercial spaces.
Urethane-cement for demanding areas
Selected systems can suit frequent washdown, heat and chemical exposure. The product, thickness, drain details and operating conditions require a separate specification.
Often considered for: processing rooms, wet commercial areas and demanding service environments.
What is included in a full-flake floor?
- Mechanical preparation and the agreed concrete repairs.
- A compatible primer or basecoat, with moisture-control measures when required.
- A full decorative flake broadcast, followed by removal of excess material.
- The specified clear topcoat and any agreed traction additive.
Browse our floor coating colour chart and send your preferred blend with your quote request. Samples help confirm the appearance before installation.
Preparation for coastal moisture and daily use
Wet vehicles, damp storage areas and older concrete are reasons to assess the slab carefully. Coating over visible moisture or weak existing paint without addressing the cause can compromise the installation.
-
1. Assess the slab and conditions
Review concrete soundness, previous coatings, contamination, cracks, drainage and moisture. Confirm the testing and acceptance requirements of the proposed system.
-
2. Prepare mechanically
Diamond grinding is common for garage floors. Heavier removal or other preparation methods may be needed to achieve the surface profile required by the selected coating.
-
3. Repair and detail the floor
Plan repairs around cracks, damaged edges, columns and drains. Moving joints need appropriate detailing; a rigid coating is not a substitute for solving movement or drainage problems.
-
4. Install and allow the correct cure
Apply the specified layers within their temperature, humidity and recoat requirements. Confirm separate reopening times for pedestrians, storage, equipment and vehicles.
Moisture resistance is not the same as waterproofing
A coating does not repair leaks, eliminate standing water or correct hydrostatic pressure. Moisture-control primers have product limits, and drainage or other building work may be needed before coating. Wet-floor traction also depends on footwear, contaminants and regular cleaning.
Hangar, marine-storage and equipment floors
For Comox aviation and equipment projects, start with the operating requirements. We review the actual fluids, rolling loads, cleaning methods and access constraints before recommending a resin flooring build.
A useful specification starts with these details
- Fluids: identify fuels, hydraulic fluids, oils, solvents and cleaning products so resistance can be checked against the selected product data.
- Traffic and details: review wheels, equipment paths, joints, thresholds and drains. Coating selection does not establish the slab’s structural load capacity.
- Storage and wet use: indoor marine and RV storage may need traction, drainage and moisture assessment; exposed decks and exterior surfaces require their own system.
- Downtime: confirm access, work zones and cure requirements before agreeing to a phased installation.
See our aircraft hangar flooring work or industrial flooring options for more project information.
How much does epoxy flooring cost in Comox?
Preliminary garage budget
$8–$12 CAD per sq. ft.
Use this as an initial planning range, not a fixed Comox installation rate. A 400 sq. ft. garage gives a base budget of approximately $3,200–$4,800.
This example is before applicable taxes, project-specific repairs, coating removal, moisture-control work and any travel or mobilization charges. The written quote confirms what is included.
What changes the final quote?
- Floor area, layout and minimum project requirements.
- Old coatings, oil contamination and concrete repairs.
- Moisture testing and any specified mitigation.
- Coating thickness, finish, texture and detailing.
- Site access, scheduling and mobilization.
Hangars, wet-use areas and larger commercial floors are priced from their own preparation and system requirements.
Get an itemized quote for your Comox project
Send the address, measurements, floor photos, intended use and preferred timing. Include close-ups of cracks, old paint, damp areas and drains. We review the scope, confirm project availability and identify whether a site assessment is needed before final pricing.
Request My Comox Flooring QuoteComox floor coating questions
Is epoxy or polyaspartic better for a Comox garage?
They can serve different roles in the same floor. Epoxy is often selected for a base layer, while a specified UV-stable polyaspartic can be used as the wear topcoat. The right combination depends on the concrete, moisture conditions, sunlight, traffic and required cure time.
Can you coat an older, cracked or previously painted floor?
Often, but the slab needs assessment first. Unsound concrete, oil, peeling paint and failed repairs must be addressed. Active cracks, moving joints or moisture may affect the repair approach or make coating unsuitable until other work is completed.
Will the floor be slippery when wet?
Traction can be adjusted with aggregate or other specified texture, but no finish is slip-proof. We balance wet-use traction with cleanability and discuss the contaminants, footwear and maintenance involved in your space.
How long does installation and curing take?
Allow for preparation, repairs, coating layers and curing. Smaller projects may take a few days, but system choice and site conditions determine the actual schedule. Foot traffic, stored items, vehicles and chemical exposure can have different reopening requirements.
Can coatings be installed during wet or cold weather?
Sometimes, if the indoor slab temperature, humidity, ventilation and moisture conditions meet the selected product requirements. Heating, moisture-control work or a different installation date may be needed. The site conditions must be verified before work starts.
Do you assess hangar and indoor marine-storage floors?
Yes. Send details of equipment, fluids, traffic, drainage and cleaning procedures. We review suitable systems and project availability. Hangars and marine workspaces need a specification matched to their actual exposures rather than a standard garage package.
Can I get a Comox quote from photos?
Photos and measurements can support a preliminary recommendation and budget. Final pricing depends on verified slab condition, access, preparation and mobilization. We confirm whether a site assessment is required before finalizing the scope.
What should I compare in quotes and warranty terms?
Compare preparation, repair allowances, moisture-control requirements, coating layers, topcoat, traction and cure instructions. Ask for the applicable workmanship and product warranty terms in writing, including exclusions and maintenance requirements.
Ready to plan your Comox floor?
Send your photos and measurements. We will review the concrete, finish options and timing so you can compare a clear scope for your garage, shop, commercial space or hangar.