Reception & corridors
Review tracked-in rain, pedestrian traffic, carts and the cleaning routine. Select colour, sheen and texture together, with clear transitions at entrances and adjoining floors.
Police facilities · Epoxy & resin systems
Police Station Flooring in Vancouver, BC
Priority One Epoxy Flooring installs resin floors for police station corridors, locker rooms, property rooms and service bays. We match the finish to each area’s traffic, cleaning and moisture exposure, with installation planned around facility access and approved work windows.
For facility teams, consultants and general contractors across Vancouver and the Lower Mainland.
Specify by room
Public, staff, service and approved secure areas.
Resolve the interfaces
Drains, coves, thresholds and movement joints.
Plan the handover
Work zones, curing and return to service.
Flooring by area
One station. Different demands underfoot.
A public entrance, a wet locker room and a vehicle bay need different finishes. Our police station flooring assessment starts with the room list, existing concrete and operational requirements, then defines a suitable resin system and installation scope for each area.
Booking & intake rooms
Plan for repeated cleaning, rolling equipment and busy circulation routes. Confirm the approved finish, wall-to-floor details and access sequence with the facility team.
Locker rooms & washrooms
Balance wet-area traction with practical cleaning. Review floor falls, drains, locker bases and cove details; a coating alone does not correct ponding or replace a specified waterproofing assembly.
Property & equipment rooms
Assess shelving, trolley routes and equipment loads. A continuous resin finish can simplify cleaning, while damaged joints and thresholds need separate attention before coating.
Vehicle & maintenance bays
Match the system to tyre traffic, oils, cleaning chemicals and washdown conditions. Check drainage, contamination and the required vehicle return-to-service window.
Holding & secure rooms
Review these areas against the owner’s approved specification. Resin type, edges, coves, penetrations and repair details must be accepted for the particular room before installation.
Systems & interfaces
Choose the finish. Specify the complete build.
Solid-colour epoxy, decorative flake and quartz-broadcast systems offer different appearances and textures. Primer, resin layers, aggregate and topcoat must work together for the assessed substrate and room use.
For wet or demanding service areas, we review whether a different resin build or a specified membrane assembly is needed. Chemical resistance is checked against the actual products, concentrations and exposure conditions.
Explore colours & finish options- Concrete & moisture Inspect existing coatings, adhesives, contamination, cracks and moisture conditions. Define preparation, repairs and primer requirements before committing to the finish.
- Texture & cleaning Review a sample against footwear, water exposure, wheeled traffic and cleaning equipment. More texture changes both traction and the effort required to clean the floor.
- Coves, drains & thresholds Detail wall junctions, drain edges and adjoining floors. Movement joints require compatible treatment; they should not simply disappear under a rigid coating.
- Approved secure-area details Agree on the flooring assembly and interfaces with the responsible project team. A seamless appearance alone does not establish suitability for a holding room.
Police facility spaces
Flooring decisions begin with the space.
Police facilities combine secure rooms, circulation routes and controlled building access. Each area needs its own review of floor interfaces, maintenance requirements and the installation sequence.
.jpg/960px-Day_80_-_Custody_cell_(8576353869).jpg)
Installation planning
Plan the work around a functioning station.
Phasing is considered before installation. The facility team confirms available rooms, temporary routes, contractor access and closure windows. Preparation and curing may require a room or zone to be taken out of service.
Survey the areas
Review the room schedule, slab condition, existing finishes, moisture exposure and drawings available for pricing.
Agree on the scope
Confirm repairs, finish samples, interfaces, work zones, dust management, ventilation and facility access conditions.
Work in approved zones
Prepare and repair the substrate, then install the agreed system within the approved sequence and site conditions.
Confirm return to use
Set separate milestones for foot traffic, equipment, wet cleaning and vehicle use using the selected system’s cure requirements.
Project scope & pricing
Start with a clear flooring brief.
Pricing depends on more than floor area. Removal, concrete repairs, moisture treatment, resin build, coves, drainage details and phased access all affect the scope.
- Room types and approximate floor area.
- Existing floor condition and permitted site photos.
- Cleaning products, water exposure and equipment traffic.
- Required finish, drawings or consultant specifications.
- Access restrictions and target reopening dates.
Questions before specification
Police station flooring questions.
Is epoxy suitable for every area in a police station?
No. Epoxy and resin systems can suit many concrete corridors, staff areas, storage rooms and service spaces. The room’s moisture, cleaning, traffic, comfort and security requirements determine suitability. Fitness spaces and other specialist rooms need separate review.
Can resin flooring be used in holding cells?
Only where the complete assembly is specified and approved for the room. The owner and responsible design team must review resin properties, wall-to-floor junctions, edges, joints and penetrations. An ordinary commercial coating should not be assumed suitable.
Can locker-room and washroom floors be slip-resistant?
Texture can be selected for the expected water exposure, footwear and cleaning routine. Review a sample before approval and resolve drainage at the same time. No finish removes the need for cleaning, spill control and maintenance.
Can the station stay open during installation?
Some projects can be divided into approved work zones while other areas remain in use. Feasibility depends on alternative routes, dust and ventilation controls, access and curing. The area being prepared and coated may need a full closure.
How soon can the floor return to service?
Timing depends on the resin system, preparation and repairs, temperature, humidity and intended use. Foot traffic, equipment, vehicle use and wet cleaning can have different release times. Confirm these milestones in the project schedule.
Can a coating go over existing tile or an old painted floor?
The existing floor must be assessed first. Weak coatings, incompatible adhesives and unsuitable tile assemblies may require removal. Preparation, moisture conditions and adhesion requirements determine the accepted substrate.
Image credits
- Custody corridor: West Midlands Police · CC BY-SA 2.0.
- Secure-room interior: West Midlands Police · CC BY-SA 2.0.
- Station entrance: Rept0n1x · CC BY-SA 3.0.
Images resized and cropped for display.
Vancouver & Lower Mainland
Bring us the room list.
We’ll help define the floor.
Discuss the concrete, finish requirements and available work windows with Priority One Epoxy Flooring. Share approved project information through your facility’s permitted process.